The Woodruff School

SUMMARY

Many technological hurdles remain before a viable commercial magnetic fusion energy reactor can be constructed, including the development of plasma-facing components with long lifetimes that can survive the harsh environment inside a reactor. One such component, the divertor, which maintains the purity of the plasma by removing fusion byproducts from the reactor, must be able to accommodate very large incident heat fluxes of at least 10 MW/m^2 during normal operation. Modular helium-cooled tungsten divertors are one of the leading divertor designs for future commercial fusion reactors, and a number of different candidates have been proposed including the modular He-cooled divertor concept with pin array (HEMP), the modular He-cooled divertor concept with multiple-jet-cooling (HEMJ), and the helium-cooled flat plate (HCFP). These three designs typically operate with helium coolant inlet temperatures of 600 �C and inlet pressures of 10 MPa. Performing experiments at these conditions to evaluate the thermal performance of each design is both challenging and expensive. An alternative, more economical approach for evaluating different designs exploits dynamic similarity. Here, geometrically similar mockups of a single divertor module are tested using coolants at lower temperatures and pressures. Dynamically similar experiments were performed on an HEMP-like divertor with helium and argon at inlet temperatures close to room temperature, inlet pressures below 1.4 MPa, and incident heat fluxes up to 2 MW/m^2. The results are used to predict the maximum heat flux that the divertor can accommodate, and the pumping power as a fraction of incident thermal power, for a given maximum tungsten temperature. A new nondimensional parameter, the thermal conductivity ratio, is introduced in the Nusselt number correlations which accounts for variations in the amount of conduction heat transfer through the walls of the divertor module. Numerical simulations of the HCFP divertor are performed to investigate how the thermal conductivity ratio affects predictions for the maximum heat flux obtained in previous studies. Finally, a helium loop is constructed and used to perform dynamically similar experiments on an HEMJ module at inlet temperatures as high as 300 �C, inlet pressures of 10 MPa, and incident heat fluxes as great as 4.9 MW/m^2. The correlations generated from this work can be used in system codes to determine optimal designs and operating conditions for a variety of fusion reactor designs.

SUBJECT:	Ph.D. Dissertation Defense

BY:	Brantley Mills

TIME:	Friday, May 30, 2014, 2:00 p.m.

PLACE:	Love Building, 109

TITLE:	On the Use of Dynamically Similar Experiments to Evaluate the Thermal Performance of Helium-Cooled Tungsten Divertors

COMMITTEE:	Dr. Said Abdel-Khalik, Co-Chair (NRE) Dr. Minami Yoda, Co-Chair (ME) Dr. Nolan Hertel (NRE) Dr. Roman Grigoriev (PHYS) Dr. Mark Tillack (UCSD)

SUMMARY Many technological hurdles remain before a viable commercial magnetic fusion energy reactor can be constructed, including the development of plasma-facing components with long lifetimes that can survive the harsh environment inside a reactor. One such component, the divertor, which maintains the purity of the plasma by removing fusion byproducts from the reactor, must be able to accommodate very large incident heat fluxes of at least 10 MW/m^2 during normal operation. Modular helium-cooled tungsten divertors are one of the leading divertor designs for future commercial fusion reactors, and a number of different candidates have been proposed including the modular He-cooled divertor concept with pin array (HEMP), the modular He-cooled divertor concept with multiple-jet-cooling (HEMJ), and the helium-cooled flat plate (HCFP). These three designs typically operate with helium coolant inlet temperatures of 600 �C and inlet pressures of 10 MPa. Performing experiments at these conditions to evaluate the thermal performance of each design is both challenging and expensive. An alternative, more economical approach for evaluating different designs exploits dynamic similarity. Here, geometrically similar mockups of a single divertor module are tested using coolants at lower temperatures and pressures. Dynamically similar experiments were performed on an HEMP-like divertor with helium and argon at inlet temperatures close to room temperature, inlet pressures below 1.4 MPa, and incident heat fluxes up to 2 MW/m^2. The results are used to predict the maximum heat flux that the divertor can accommodate, and the pumping power as a fraction of incident thermal power, for a given maximum tungsten temperature. A new nondimensional parameter, the thermal conductivity ratio, is introduced in the Nusselt number correlations which accounts for variations in the amount of conduction heat transfer through the walls of the divertor module. Numerical simulations of the HCFP divertor are performed to investigate how the thermal conductivity ratio affects predictions for the maximum heat flux obtained in previous studies. Finally, a helium loop is constructed and used to perform dynamically similar experiments on an HEMJ module at inlet temperatures as high as 300 �C, inlet pressures of 10 MPa, and incident heat fluxes as great as 4.9 MW/m^2. The correlations generated from this work can be used in system codes to determine optimal designs and operating conditions for a variety of fusion reactor designs.